Search
Skip to Search Results- 2Hogan, James D.
- 2Kannan, Rangasayee
- 1Ali, Mostafa A A
- 1Bineshmarvasti, Baher
- 1Desalegne, Admasu S.
- 1Dewar, Matthew P
- 24Graduate and Postdoctoral Studies (GPS), Faculty of
- 24Graduate and Postdoctoral Studies (GPS), Faculty of/Theses and Dissertations
- 2Civil and Environmental Engineering, Department of
- 2Civil and Environmental Engineering, Department of/Structural Engineering Reports
- 2Mechanical Engineering, Department of
- 2Mechanical Engineering, Department of/Journal Articles (Mechanical Engineering)
- 5Driver, Robert (Civil and Environmental Engineering)
- 5Henein, Hani (Chemical and Materials Engineering)
- 2Imanpour, Ali (Civil and Environmental Engineering)
- 2Mitlin, David (Chemical and Materials Engineering)
- 2Thundat, Thomas (Chemical and Materials Engineering)
- 1Ben-Zvi, Amos (Chemical and Materials Engineering)
-
Fall 2019
An evaluation of the resistance of two different X70 pipeline steels to hydrogen-induced cracking in severe (pH 2.7 and 1 atm H2S) and intermediate (pH 5.5 and 1 atm H2S) sour service conditions was undertaken. The two steels used in this work, X70-X and X70-B, were selected based on their...
-
Fall 2014
Seismic velocity dispersion in crystalline rock is investigated through experimental measurements on two natural quartzite specimens. The quartzites are thermally damaged to induce low aspect ratio cracks and the shear and Young’s moduli are measured across a range of effective pressures, from...
-
Extracting and Integrating Industrial Construction Steel Trade Data in ill-formed BIM Models
DownloadFall 2017
Oil and gas are known for their huge-size and complex projects that consist of multiple trades’ subprojects such as concrete, steel, and piping. These subprojects are executed within a confined area during a limited time frame. This requires careful planning and coordination between these...
-
Spring 2012
Coped beams are susceptible to fatigue cracking in the web at the cope radius when subjected to tension in the coped region. Use of an adhesively bonded composite patch over the crack can reduce the stress concentration and delay further crack growth. This report contains the results of a...
-
Functionalization and Characterization of Metal Oxide Coatings of Stainless Steel and Silica Nanoparticles
DownloadSpring 2013
The development of tolerogens, fabricated devices eliciting tolerance toward incompatible donor ABO antigens in implant patients, is the ultimate goal of this project. This would permit ABO incompatible organ transplants, increase the donor pool for patients, increase efficiency in the use of...
-
Fall 2017
Casing pipes used in sour service are prone to two forms of failure: hydrogen induced cracking (HIC) and sulfide stress cracking (SSC). The objective of this thesis is to investigate the resistance of L80 ERW and Seamless steel pipe, with five different chemical compositions, to both HIC and SSC....
-
2018-01-01
Kennedy, J.R., Wiskel, J.B., Ivey, D.G., Henein, H.
The potential exists to use ultrasonic shear velocity for real time microstructure assessment of the quenching step in the teat treatment of L80 steel pipe. L80 steel samples were austenitized and subsequently cooled in different quench mediums (water, oil, heated oil, air and furnace) to produce...
-
Spring 2019
The formation of bainite is the most studied and the most debated phase transformation in steels, with research spanning almost a century. With two theories of transformation, the transformation mechanism of bainite is still a disputed subject among physical metallurgists. Upper bainite and lower...
-
Modeling of the Effect of Run-out Table Cooling on the Microstructure of a Thick Walled X70 Skelp
DownloadSpring 2018
This thesis presents work performed to model and measure the effect of run-out table cooling on a thick walled X70 steel. During run-out table cooling, the steel undergoes several phase transformations that will affect its microstructure, and thus, its mechanical properties. To predict the steel...
-
Fall 2011
Optimization techniques, in conjunction with a finite element thermal model, are used in this thesis to optimize the temperature profile (i.e. cooling rate and coiling temperature) of a steel skelp during laminar cooling. Optimization parameters include skelp velocity, laminar cooling bank...