Search
Skip to Search Results- 17Chemical and Materials Engineering, Department of
- 17Chemical and Materials Engineering, Department of/Research Articles and Materials (Chemical and Materials Engineering)
- 4Graduate and Postdoctoral Studies (GPS), Faculty of
- 4Graduate and Postdoctoral Studies (GPS), Faculty of /Theses and Dissertations
-
Fall 2013
This study used non-intrusive, optical based measurement techniques in a parametric study of a flash atomized jet. The bench scale water spray was operated at pressure ratios ranging from 6.80-17.0 and degrees of superheat of 20-80 °C. This broad range of parameters allowed for the evaluation of...
-
A Study of Rapidly Solidified Al1.5wt%/3wt%Mg0.2wt%Sc Powders and Strips using Impulse Atomization
DownloadFall 2016
In this work, rapid solidification microstructures and mechanical properties of Al1.5Mg0.2Sc and Al3Mg0.2Sc are investigated. Samples in the form of powders and strips / deposits of different thermal histories are obtained by means of impulse atomization technique. Cooling rates of the powders,...
-
2016-01-01
Bogno, A.-A., Riveros, C., Henein, H., Li, D.
This paper investigates amorphous phase formation and rapid solidification characteristics of a CoCr alloy. High cooling rate and high undercooling-induced rapid solidification of the alloy was achieved by impulse atomization in helium atmosphere. Two atomization experiments were carried out to...
-
Characterization of a {(Fe60Co40)75B20Si5}96Nb4 Impulse Atomized Glassy Powder by Neutron Diffraction and Differential Scanning Calorimetry
Download2015-01-01
Bogno, A.-A., Dahlborg, U., Calvo-Dahlborg, M., Riveros, C., Ciftci, N., Henein, H., Sediako, D.
This paper investigates FeCo-based alloy glass formability by high undercooling and high cooling rate solidification technique and the hardness evaluation of the generated samples. For this investigation, Impulse Atomization was used to generate {(Fe60Co40)75B20Si5}96Nb4 powders of different...
-
2016-01-01
Bedel, M., Reinhart, G., Bogno, A.-A., Gandin, Ch.-A., Jacomet, S., Boller, E., Nguyen-Thi, H., Henein, H.
The Impulse Atomization process developed at the University of Alberta (Canada) enables metallic powders to be solidified with well controlled process parameters. The inner microstructure of several droplets of Al-4.5wt.%Cu alloy produced by this technique has been investigated by using both...
-
Design and processing conditions of hypoeutectic Al-Cu-Sc alloys for maximum benefit of scandium
Download2017-01-01
Bogno, A.-A., Henein, H., Gallerneault, M.
Addition of Sc to Al-Cu is reported to be responsible for a high precipitation hardening upon heat treatment and serves as a good grain refiner. However, Scandium is presently very expensive, therefore, getting maximum benefit from a minimum addition would be economically of value. This work...
-
EFFECTS OF SCANDIUM ON HYPO-EUTECTIC ALUMINUM COPPER MICROSTRUCTURES UNDER LOW SOLIDIFICATION RATE CONDITIONS
Download2017-11-01
Bogno, A.-A., Valloton, J., Henein, H., Ivey, D.G., Locock, A.J., Gallerneault, M.
This work addresses the microstructures and mechanical properties of Al-4.5 wt% Cu alloys containing 0.1, 0.2 and 0.4 wt% Sc that were solidified under low cooling rate conditions (< 1ºC/s) and then heat treated. The samples were solidified in a differential scanning calorimeter before being heat...
-
2019-01-01
Bogno, A.-A., Henein, H., Ivey, D.G., Valloton, J., Reinhart, G., Sediako, D., Gallerneault, M.
This paper reports on the characterization of rapidly solidified Al-4.5 wt% Cu-xSc (x= 0.1, 0.2 or 0.4 wt %). The effect of micro-additions of Sc (up to 0.4 wt %) was examined through microstructural analysis of rapidly solidified, as well as aged samples, by means of electron microscopy, x-ray...
-
Estimation of Droplet Size and Temperature at which Solidification starts in a Drop Tube-Impulse System.
Download2016-01-01
Delshad Khatibi, P., Henein, H.
D2 tool steel powders were produced using a drop tube-impulse atomization technique. In order to measure the radiant energy and droplet size of atomized D2 steel droplets, DPV-2000 (Tecnar Automation Ltée, St. Hubert Quebec, Canada) was utilized. In-situ velocity and droplet size of the atomized...
-
2017-01-01
Valloton, J., Herlach, D.M., Henein, H., Sediako, D.
Rapid solidification of D2 tool steel is investigated experimentally using ElectroMagnetic Levitation (EML) under terrestrial and reduced gravity conditions and Impulse Atomization (IA), a drop tube type of apparatus. IA produces powders 300 to 1400 μm in size. This allows the investigation of a...