Search
Skip to Search Results- 3Hogan, James D.
- 2Carey, Jason P.
- 2McDonald, André
- 2Melenka, Garrett W.
- 2Santhanakrishnan, Ananthan
- 2Shao, Chenwei
- 28Graduate and Postdoctoral Studies (GPS), Faculty of
- 28Graduate and Postdoctoral Studies (GPS), Faculty of /Theses and Dissertations
- 7Mechanical Engineering, Department of
- 6Mechanical Engineering, Department of/Journal Articles (Mechanical Engineering)
- 2WISEST Summer Research Program
- 2WISEST Summer Research Program/WISEST Research Posters
- 9Department of Mechanical Engineering
- 7Department of Chemical and Materials Engineering
- 6Department of Civil and Environmental Engineering
- 2Department of Chemistry
- 1Department of Biomedical Engineering
- 1Department of Earth and Atmospheric Sciences
- 3Bindiganavile, Vivek (Civil and Environmental Engineering)
- 2Boluk, Yaman (Civil and Environmental Engineering)
- 2Henein, Hani (Chemical and Materials Engineering)
- 1Al-Hussein, Mohamed (Civil and Environmental Engineering)
- 1Ayranci, Cagri (Mechanical Engineering)
- 1Bindiganavile, Vivek (Civil and Environmental Engineering)
-
A Fully 3D Printed Waveguide and its Application as Microfluidically Controlled Waveguide Switch
DownloadFall 2016
Hollow rectangular waveguides are employed extensively in microwave and millimeter wave devices owing to their relatively high power handling capabilities and low losses, particularly at higher frequencies, compared to transmission lines. However, the fabrication of such metal waveguides suffer...
-
A Novel 3D Printed Brace Manufacturing Process for the Treatment of Adolescent Idiopathic Scoliosis
DownloadSpring 2019
Adolescent Idiopathic Scoliosis (AIS) is a three-dimensional spinal deformity with lateral curvature and axial vertebral rotation affecting 1-3% of adolescents. Bracing is a proven non-surgical treatment aiming to stop curve progression. Literature has shown that brace wear time affects brace...
-
Additive Manufacturing of Shape Memory Polymers: Effects of Print Orientation and Infill Percentage on Mechanical and Shape Memory Recovery Properties
DownloadFall 2017
Material Extrusion Additive Manufacturing (MEAM), also known as Fused Deposition Modeling (FDM), is a manufacturing technique in which three-dimensional objects are built. These objects are built by repeatedly extruding thin layers of molten materials through a nozzle in different paths and...
-
Spring 2018
Shape memory polymers (SMPs) can be used in many critical applications, including biomedical and aerospace fields, due to their ability to recover their original/permanent shape from a deformed/temporary shape upon application of a stimulus. SMPs are subjected to bending in a large number of...
-
Characterization of Electroless Ni-P Coatings and Electrodeposition of Ni Coatings for Electrodes in Zinc-Air Flow Batteries
DownloadFall 2023
Electrochemical energy storage devices such as Li-ion or Zn-air batteries (ZABs) are utilized to store energy generated by renewable sources, since these sources are intermittent. Li-ion batteries uses flammable organic electrolytes (less safe than nonflammable aqueous electrolytes) and have high...
-
Spring 2016
Polypropylene (PP) is a thermoplastic polymer and is one of the most widely used polyolefin polymer, which is a well-known semi crystalline polymer. Plastics such as polypropylene are commonly used for different applications and purposes due to their versatility; however, it should be noted that...
-
Fall 2019
Cutting the pavement to install a small diameter utility network, such as flexible pipes, conduits or telecommunication lines, is a common practice in urban areas. The last 200 meters of installation is known particularly difficult to deliver, with obstacles both above and below ground to...
-
2021-04-30
Pang, Wanying, Wang, Yingnan, Jin, Zhehui
Shale/tight gas plays an increasingly important role to meet the growing global energy demand and reduce carbon emissions. Unlike conventional reservoirs, shale formations are subject to rock heterogeneity and have pore size distributions ranging from sub-1 nm to a few micrometers. Thanks to the...
-
Design and system identification for a plasma transferred arc additive manufacturing technology
DownloadFall 2021
The increase in the pace of development of additive manufacturing technology opens new markets and expands the scope of research and knowledge. Additive manufacturing, previously known as rapid prototyping, can employ advanced state-of-the-art materials, such as metal composites, in metal 3D...