ERA Banner
Download Add to Cart Share
More Like This
  • http://hdl.handle.net/10402/era.24832
  • Non-Equilibrium Containerless Solidification of Al-Ni Alloys
  • Ilbagi,Arash
  • English
  • Rapid solidification
    Peritectic
    Cooling rate
    Rietveld analysis
    micro-tomography
  • Dec 19, 2011 3:31 PM
  • Thesis
  • English
  • Adobe PDF
  • 16787344 bytes
  • More than 90% of all metallic materials are manufactured starting from their liquid state. Designing the solid structure produced during solidification can have major savings in downstream processing. Rapid solidification yields significant enhancement in properties through refined microstructure, reduced microsegregation and the formation of metastable phases. To control the microstructure obtained from rapid solidification and attain desired properties, understanding of effects of processing parameters, in particular cooling rate and undercooling on microstructure evolution is required. In the case of peritectic reaction this understanding is lacking. In this dissertation, the effect of cooling rate on the peritectic reactions occurring in the binary Al-Ni system is investigated. Impulse Atomization technique was used to produce rapidly solidified particles of Al-36 wt%Ni and Al-50wt%Ni. The effect of cooling rate on the microstructure evolution and phase fractions achieved after solidification was studied. Also, porosity formation in the atomized particles was investigated and the effect of processing parameters on the amount and distribution of porosity was analyzed. For characterization, neutron diffraction, X-ray micro-tomography, electron and optical microscopy were utilized. The results showed that in both Al-36 wt%Ni and Al-50 wt%Ni, cooling rate has a significant effect on the formation of microstructure, phase fractions and metastable phase formation. It was shown that at different cooling rate regimes different mechanisms are responsible for the changes observed in the phase fractions. Using X-Ray tomography, multiple nucleation sites were observed in large particles, while smaller particles contained only a single nucleation site. Also, porosity within the particles was quantified and the distribution of porosity with regard to the nucleation site and cooling rate is discussed. The distribution of porosity within the small particles and large particles was found to be significantly different. Quantitative analysis of the micro-tomography images revealed that the volume percent of porosity decreased with increasing cooling rate. Also, it was found that for higher cooling rates, porosity tends to form closer to the periphery of the particles, whereas at lower cooling rates the pores are more randomly distributed.
  • H. Henein, A. Ilbagi and Ch.-A. Gandin, “Quantitative analysis of alloy structures solidified under limited diffusion conditions”, in Contairnerless Unidercooling of Drople and Droples. Edited by D.M. Herlach and D. M. Matson, WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim, ISBN 978-3-527-33122-2.
    A. Ilbagi, P. Delshad Khatibi, I. P. Swainson, G. Reinhart and H. Henein, "Microstructural analysis of rapidly solidified aluminium-nickel alloys", Canadian Metallurgical Quarterly, Vol. 50, No. 3, 2011, 295-302.
    A. Ilbagi, H. Henein and A. B. Phillion "Phase Quantification of Impulse Atomized Al68.5Ni31.5 Alloy", Journal of Materials Science, (2011) 46:6235–6242
    A. Ilbagi, P. Delshad Khatibi and H. Henein, "Effect of cooling rate on solidification of Al-Ni alloys", J. Phys: Conf. Ser. 327 012010.
  • Doctoral
  • Doctor of Philosophy
  • Department of Chemical and Materials Engineering
  • Materials Engineering
  • Spring 2012
  • Henein,Hani
  • Matson,Douglas (Tufts University, Mechanical Engineering)
    Herd,Christopher (Earth and Atmospheric Sciences)
    Ivey,Douglas (Chemical and Materials Engineering)
    Chen,Weixing (Chemical and Materials Engineering)