ERA

Download the full-sized PDF of Integrated Hollow-Core Microcavity Arrays - Building Blocks for Optical Sensing and Quantum InformationDownload the full-sized PDF

Analytics

Share

Permanent link (DOI): https://doi.org/10.7939/R3416TD01

Download

Export to: EndNote  |  Zotero  |  Mendeley

Communities

This file is in the following communities:

Graduate Studies and Research, Faculty of

Collections

This file is in the following collections:

Theses and Dissertations

Integrated Hollow-Core Microcavity Arrays - Building Blocks for Optical Sensing and Quantum Information Open Access

Descriptions

Other title
Subject/Keyword
Integrated Optics, Microcavity
Type of item
Thesis
Degree grantor
University of Alberta
Author or creator
Bitarafan, Mohammadhossein
Supervisor and department
DeCorby, Ray (Electrical and Computer Engineering)
Examining committee member and department
Iyer, Ashwin (Electrical and Computer Engineering)
Tsui, Ying (Electrical and Computer Engineering)
Van, Vien (Electrical and Computer Engineering)
Reiserer, Andreas (Max Planck Institute)
Reformat, Marek (Electrical and Computer Engineering)
Department
Department of Electrical and Computer Engineering
Specialization
Photonics and Plasmas
Date accepted
2017-09-29T14:37:56Z
Graduation date
2017-11:Fall 2017
Degree
Doctor of Philosophy
Degree level
Doctoral
Abstract
This thesis describes an experimental and theoretical study of a novel class of air-core microcavities on chips, monolithically fabricated by the controlled formation of delamination buckles within a-Si/SiO2-based multilayer thin film stacks. First, arrays of dome-shaped microcavities were fabricated via buckling over circularly patterned low-adhesion films. The stress-driven self-assembly process produces cavities with highly predictable geometries matching with elastic buckling theory. Optical experiments revealed reflectance-limited finesse of >10^3, implying low roughness and minimal defects. These devices were aimed at operating in a fundamental mode regime; thus, mode volumes as low as ~1.3λ^3 and potential for single-atom cooperativity of ~50 were achieved, making this type of cavities an interesting candidate for quantum-optics applications. Next, the viability of providing open-access to the core of the buckled-dome microcavities was explored by fabricating dome-shaped microcavities intersecting with hollow waveguide channels. Optical studies showed that connection to channels had minimal adverse effects on the morphological symmetry of the aforementioned devices, especially at the center where the optical modes reside. This monolithic approach, accordingly, holds promise to enable the introduction of liquid or gaseous analytes into the core of this class of microcavities. The possibility for open-access to the cavity volume, along with good optical properties, makes these cavities good candidates for applications in sensing and cavity quantum electrodynamics (CQED). The buckled upper mirror in the dome-shaped microcavities is inherently a flexible plate, which thus allows interesting options for tuning the resonance wavelength. Hence, comprehensive studies were carried out to analytically and experimentally examine the temperature dependence of the resonance wavelength of the buckled microcavities. Aiming to explore their potential for optomechanical studies, the effective spring constant and mechanical mode frequencies of the buckled domes were also experimentally and theoretically studied. Related to their thermal tunability, absorption by the mirror layers of light circulating inside the core of dome-shaped cavities at or near resonance gives rise to nonlinear effects. For optical input powers in the W range, we observed bistability in the output transmission spectra of the above-mentioned resonators. This behavior, which we showed to arise mainly due to photothermal effects, was studied analytically using first-order approximations, and the predictions were shown to be in good agreement with experimental results. Finally, the buckling process was employed to fabricate a novel class of three-dimensional (3D) microcavities, in which the lateral confinement is provided by Bragg mirrors while axial (in-plane) confinement is provided by mode cutoff sections in the hollow waveguides. The cutoff sections were implemented as back-to-back dual tapers, which can be realized easily using the buckling-based fabrication processes. Optical experiments on numerous dual-tapers confirmed high reflection in wavelength ranges subject to cutoff, and high transmission at shorter wavelengths. Thus, the dual tapers can be used as a novel type of waveguide-based short-pass filter. Additionally, 3D microcavities were fabricated by cascading two dual-taper waveguides. Optical experiments revealed Q > 10^4 along with mode volume ~100λ^3 , which promises a cooperativity of C > 1, making them of great interest in quantum information studies. Furthermore, this approach to forming axially varying hollow waveguides on chips is expected to provide new strategies for controlling the dispersion and confinement of light within optofluidic and CQED systems.
Language
English
DOI
doi:10.7939/R3416TD01
Rights
This thesis is made available by the University of Alberta Libraries with permission of the copyright owner solely for the purpose of private, scholarly or scientific research. This thesis, or any portion thereof, may not otherwise be copied or reproduced without the written consent of the copyright owner, except to the extent permitted by Canadian copyright law.
Citation for previous publication
M. H. Bitarafan and R. G. DeCorby, "On-chip high-finesse Fabry-Perot microcavities for optical sensing and quantum information,'' Sensors, vol. 17, no. 8, p. 1748, 2017M. H. Bitarafan, H. Ramp, T. W. Allen, C. Potts, X. Rojas, A. J. R. MacDonald, J. P. Davis, and R. G. DeCorby, "Thermomechanical characterization of on-chip buckled dome Fabry-Perot microcavities,'' JOSA B, vol. 32, no. 6, pp. 1214-1220, 2015M. Bitarafan, H. Ramp, C. Potts, T. Allen, J. Davis, and R. DeCorby, "Bistability in buckled dome microcavities,'' Optics letters, vol. 40, no. 22, pp. 5375-5378, 2015M. H. Bitarafan, C. A. Potts, and R. G. DeCorby, "Cutoff-based dual-taper reflectors in on-chip hollow waveguides,'' Optics Express, vol. 25, no. 5, pp. 5101-5106, 2017

File Details

Date Uploaded
Date Modified
2017-09-29T20:37:57.171+00:00
Audit Status
Audits have not yet been run on this file.
Characterization
File format: pdf (PDF/A)
Mime type: application/pdf
File size: 8617062
Last modified: 2017:11:08 16:59:47-07:00
Filename: Bitarafan_Mohammad_201709_PhD.pdf
Original checksum: 8ee7c0ffc1f455be7cce0bb892c6b8fd
Activity of users you follow
User Activity Date