Journal Articles (Mechanical Engineering)
Items in this Collection
- 52Kumar, Amit
- 46Hogan, James D.
- 30Carey, Jason P.
- 17Major, Paul W.
- 15Hogan, James
- 13Melenka, Garrett W.
- 12Life Cycle Assessment
- 8Brittle failure
- 8Digital image correlation
- 8Dynamic fragmentation
- 7Boron carbide
- 7GHG Emissions
- 236Mechanical Engineering, Department of
- 236Mechanical Engineering, Department of/Journal Articles (Mechanical Engineering)
- 1Earth and Atmospheric Sciences, Department of
- 1Earth and Atmospheric Sciences, Department of/Journal Articles (Earth and Atmospheric Sciences)
- 1Physics, Department of
- 1Physics, Department of/Journal Articles (Physics)
-
Multi-Objective Optimization Framework for Landmark Measurement Error Correction in Three Dimensional Cephalometric Tomography
Download2013
Lagravère, Manuel O., Carey, Jason P., DeCesare, Alessandro, Secanell, Marc
The purpose of this study is to minimize errors that occur when using a four vs six landmark superimpositioning method in the cranial base to define the co-ordinate system. Cone beam CT volumetric data from ten patients were used for this study. Co-ordinate system transformations were performed....
-
2015-01-01
Pant, L. M., Mitra, S. K., Secanell, Marc
A reconstruction methodology based on different-phase-neighbor (DPN) pixel swapping and multigrid hierarchical annealing is presented. The method performs reconstructions by starting at a coarse image and successively refining it. The DPN information is used at each refinement stage to freeze...
-
2023-03-01
Shao, Chenwei, Li, Haoyang, Zhu, Yankun, Li, Peng, Yu, Haoyang, Zhang, Zhefeng, Gleiter, Herbert, McDonald, André, Hogan, James D.
Nanostructured materials are being actively developed, while it remains an open question how to rapidly scale them up to bulk engineering materials for broad industrial applications. This study propose an industrial approach to rapidly fabricate high-strength large-size nanostructured metal...
-
2015-01-01
Shahrukh, Hassan, Oyedun, Adetoyese Olajire, Kumar, Amit, Ghiasi, Bahman, Kumar, Linoj, Sokhansanj, Shahab
A process model was developed to determine the net energy ratio (NER) for both regular and steam-pretreated pellet production from ligno-cellulosic biomass. NER is a ratio of the net energy output to the total net energy input from non-renewable energy source into the system. Scenarios were...
-
2019-01-01
Pare, Phililp E., Hashemi, Ehsan, Stern, Raphael, Sandberg, Henrik, Johansson, Karl Henrik
This paper proposes a cooperative adaptive cruise control model, adding a communication network structure to an existing model that has been shown to capture real commercial adaptive cruise control vehicle behavior. The proposed model is interesting because it only requires minimal information...
-
2017
We present an analysis of the superposed incremental deformations of lipid membranes in contact with a circular substrate. A complete analytical solution describing the morphological transitions of lipid membranes is obtained via Monge parametric representation and admissible linearization. The...
-
2016
Farbaniec, Lukasz, Daphalapurkar, Nitin, Ramesh, K.T., Hogan, James
Dynamic brittle fragmentation is typically described using analytical and computational approaches for tensile stress-states. However, most fragmentation applications (e.g., impact, blast) involve very large initial compressive stresses and deformations. In this study, the compressive...
-
On the evaluation of mechanical properties and ballistic performance of two variants of boron carbide
Download2021-06-01
Lo, Calvin, Li, Haoyang, Toussaint, Geneviève, Hogan, James D.
A comparative study on the microstructure, rate-dependent compressive behavior, and ballistic performance of commercially available pressureless sintered boron carbide-titanium diboride (material Z) and hot-pressed boron carbide (material S) was conducted. Under quasi-static compression at rates...
-
On the microstructure-dependency of mechanical properties and failure of low-pressure cold-sprayed tungsten carbide-nickel metal matrix composite coatings
Download2020-08-25
Munday, Guriqbal, Hogan, James D., McDonald, André
This study improves upon understanding of the effects of reinforcing particle content and microstructure on the mechanical properties and failure of low-pressure cold spray fabricated tungsten carbide-nickel (WC-Ni) metal matrix composite (MMC) coatings. Image analyses were performed on scanning...